
Module Quang OPTONE SFP+-10GB-LR
Product Description
The SFP+-10GB-LR series single mode transceiver is small form factor pluggable module for serial optical data communications such as IEEE 802.3ae 10GBASE-LR/LW. It is with the SFP+ 20-pin connector to allow hot plug capability.
This module is designed for single mode fiber and operates at a nominal wavelength of 1310nm. The transmitter section uses a 1310nm multiple quantum well DFB laser and is a class 1 laser compliant according to International Safety Standard IEC-60825.
The receiver section uses an integrated InGaAs detector preamplifier ( IDP ) mounted in an optical header and a limiting post-amplifier IC.

Features
Applications
Module Quang OPTONE SFP+-10GB-LR
Recommended Operating Conditions
| Parameter | Symbol | Min | Typical | Max | Unit | ||||
| Operating Case Temperature |
Standard | Tc | 0 | +70 | °C | ||||
| Industria | Tc | -40 | +85 | °C | |||||
| Power Supply Voltage | Vcc | 3.15 | 3.3 | 3.45 | V | ||||
| Power Supply Current | Icc | 300 | mA | ||||||
| Surge Current | I Surge | +30 | mA | ||||||
| Baud Rate | 11.1 | Gbps | |||||||
Electrical Characteristics
| Parameter | Symbol | Min | Typical | Max | Unit | Notes | |||
| Transmitter | |||||||||
| CML Inputs(Differential) | Vin | 150 | 1200 | mVpp | AC coupled inputs | ||||
| Input AC Common Mode Voltage | 0 | 25 | mV | RMS | |||||
| Input Impedance (Differential) | Zin | 85 | 100 | 115 | ohm | Rin > 100 kohms @ DC | |||
| Differential Input S-parameter | SDD 11 | - | - | -10 | dB | ||||
| Differential to Common Mode Conversion | SCD 11 | - | - | -10 | dB | ||||
| Tx_DISABLE Input Voltage – High | 2 | 3.45 | V | ||||||
| Tx_DISABLE Input Voltage – Low | 0 | 0.8 | V | ||||||
| Tx_FAULT Output Voltage – High | 2 | Vcc+0.3 | V | Io = 400µA; Host Vcc | |||||
| Tx_FAULT Output Voltage – Low | 0 | 0.5 | V | Io = -4.0Ma | |||||
| Receiver | |||||||||
| CML Outputs (Differential) | Vout | 350 | 700 | mVpp | AC coupled outputs | ||||
| Output AC Common Mode Voltage | 0 | 15 | mV | RMS | |||||
| Output Impedance (Differential) | Zout | 90 | 100 | 110 | ohms | ||||
| Differential Output S-parameter | SD22 | - | - | -10 | dB | ||||
| Rx_LOS Output Voltage – High | 2 | Vcc+0.3 | V | lo = 400µA; Host Vcc | |||||
| Rx_LOS Output Voltage – Low | 0 | 0.8 | V | lo = -4.0Ma | |||||
| MOD_DEF ( 0:2 ) |
VoH | 2.5 | V | With Serial ID | |||||
| VoL | 0 | 0.5 | V | ||||||
Optical Characteristics
| Parameter | Symbol | Min | Typical | Max | Unit | ||||
| 9µm Core Diameter SMF | 10 | km | |||||||
| Data Rate | 11.1 | Gbps | |||||||
| Transmitter | |||||||||
| Centre Wavelength | λc | 1270 | 1310 | 1355 | nm | ||||
| Spectral Width (-20dB) | ∆λ | 1 | nm | ||||||
| Average Output Power*note1 | Pout | -6 | 0.5 | dBm | |||||
| Extinction Ratio | ER | 3.5 | dB | ||||||
| Average Power of OFF Transmitter | Poff | -30 | dBm | ||||||
| Side Mode Suppression Ratio | SMSR | 30 | dB | ||||||
| Transmitter Dispersion Penalty | TDP | 3.2 | dB | ||||||
| Input Differential Impedance | ZIN | 90 | 100 | 110 | Ω | ||||
| TX Disable Assert Time | t_off | 10 | us | ||||||
| TX_DISABLE Negate Time | t_on | 1 | ms | ||||||
| TX_BISABLE time to start reset | t_reset | 10 | us | ||||||
| Time to initialize, include reset of TX_FAULT | t_init | 300 | ms | ||||||
| TX_FAULT from fault to assertion | t_fault | 100 | us | ||||||
| Total Jitter | TJ | 0.28 | UI(p-p) | ||||||
| Data Dependant Jitter | DDJ | 0.1 | UI(p-p) | ||||||
| Uncorrelated Jitter | UJ | 0.023 | RMS | ||||||
| Receiver | |||||||||
| Centre Wavelength | λc | 1260 | 1565 | nm | |||||
| Sensitivity*note2 | Pmin | -14.4 | dBm | ||||||
| Receiver Overload | PMAX | 0.5 | dBm | ||||||
| Optical Return Loss | ORL | -12 | dB | ||||||
| LOS De-Assert | LOSD | -16 | dBm | ||||||
| LOS Assert | LOSA | -28 | dBm | ||||||
| LOS | High | 2.0 | Vcc+0.3 | V | |||||
| Low | 0 | 0.8 | B | ||||||
Module Quang OPTONE SFP+-10GB-LR