VN EN

Node Quang 870MHz WR8604JL

  • Mô tả
    1 Way Optical Node, 4 Ports Output
  • Nhà sản xuất
    Prevail
  • Giá
    Vui lòng liên hệ
  • Số lượng
Xem địa chỉ mua hàng
Mô tả Sản phẩm

Node Quang 870MHz WR8604JL is our latest high-grade four-output CATV network optical receiver. The pre-amplifier adopts full-GaAs MMIC, post-amplifier adopts GaAs module.

Optimized circuit design coupled with our 10 years professional design experience, make the equipment achieve good performance indexes.

Microprocessor control, digital display the parameters, the engineering debug is especially easy.

It is the main equipment to build the CATV network

 

FEATURE

  • High response PIN photoelectric conversion tube.

  • Optimized circuit design, SMT process production, optimized signal path, make the photoelectric signal transmission more smooth.

  • Specialized RF attenuation chip, with good RF attenuation and equilibrium linear, high accuracy.

  • GaAs amplifier device, power doubly output, with high gain and low distortion.

  • Single Chip Microcomputer (SCM) control equipment working, LCD display the parameters, convenience and intuitive operation, and stable performance.

  • Excellent AGC performance, when the input optical power range is －9～＋2dBm, the output level keep unchanged, CTB and CSO basically unchanged.

  • Reserved data communication interface, can connect with the Ethernet transponder, access to network management system.

  • Return path can select burst mode to sharply decrease the noise convergence and greatly increase the quality and reliability of network operation.

The technique parameters of this manual according to the measuring method of GY/T 194-2003 , and tested in the following conditions.

Testing conditions:

1. Forward optical receive part: with 10km standard optical fiber, passive optical attenuator and standard optical transmitter composed the testing link. Set 59 PAL-D analog TV channel signal at range of 45/87MHz～550MHz under the specified link loss. Transmit digital modulation signal at range of 550MHz～862/1003MHz, the digital modulation signal level (in 8 MHz bandwidth) is 10dB lower than analog signal carrier level. When the input optical power of optical receiver is -2dBm, the RF output level is 108dBμV, with 9dB output tilt, measure the C/CTB, C/CSO and C/N.

2. Backward optical transmit part: Link flatness and NPR dynamic range are the link indexes which is
composed of backward optical transmitter and backward optical receiver.
Note: When the rated output level is the system full configuration and the receiving optical power is -2dBm, equipment meets the maximum output level of link index. When the system configuration reduce (that is, actual transmission channels reduce), the output level of equipment will be increased. Friendly Notice: Suggest you setting the RF signal to 6~9dB tilt output in the practical engineering application to improve the nonlinear index (under the node) of the cable system.
 

Node Quang 870MHz WR8604JL

Node_Quang_870MHz_WR-8604JL

 

 

Node_Quang_870MHz_WR-8604JL

Thông số kỹ thuật
Item  Unit  Technical Parameter
Forward Part
Optical Parameter
Receive Optical Power dBm   -7 ~ +2
Optical Return Loss  dB  >45
Optical Receiving Wavelength nm  1100 ~ 1600
Connector Type    FC/APC, SC/APC or specified by the user
Fiber Type    Single Mode
Link Parameter
C/N  dB  ≥51 (-1dBm input)
C/CTB  dB  ≥65 EQ 6dB, Output level 108dBμV
C/CSO  dB  ≥60
RF Parameter
Frequency Range  MHz  45~862/1003 (or specified by the user)
Flatness in Band  dB  ±0.75
Fixed slope dB  2±0.5
Rated Output Level  dBμV  ≥ 108
Max Output Level  dBμV   ≥110 
Output Return Loss  dB  ≥14
Output Impedance  Ω  75
Fixed ATT and EQ (common use) dB 2.3.4.5.6.7.9.13 (or specified by the user)
Return Part
Optical Parameter
Optical Transmit Wavelength nm  1310±10, 1550±10 or specified by the user
Output Optical Power mV 0.5, 1, 2
Optical Connector Type   FC/APC, SC/APC or specified by the user
RF Parameter
Frequency Range  MHz  5~65 (or specified by the user)
Flatness in Band  dB  ±1
Input Level dBμV  72~85
Output Impedance  Ω  75
General Performance
Power Voltage  V  A: AC (150~265)V, B: AC (35~90)V
Operating Temperature ℃   -40~60
Storage Temperature ℃   -40~65
Relative Humidity % (-9dBm/-8dBm/-7dBm/-6dBm/-5dBm/-4dBm) — (+2dBm) adjustable
Consumption  VA  ≤30
Dimension mm 240 (L)×240 (W)×150 (H)
Burst Mode (Select this mode, see below)
Optical Output Power (Close the burst mode) dBm  -30
Laser Turn On Threshold dBμV  ≥70
Laser Turn Off Threshold dBμV  ≤62
Laser Turn On Time (t1) us 0.5 ≤ t1 ≤ 1
Laser Turn Off Time (t2) us 0.5 ≤ t2 ≤ 1.5

 

Common Failure Analysis and Troubleshooting:

Failure phenomenon  Failure cause  Solution
After connecting the network, the image of the optical contact point has obvious netlike curve or large particles highlights but the image background is clean. 1. The optical input power of the optical receiver is too high, make the output level of the optical receiver module too high and RF signal index deteriorate.
2. The RF signal (input the optical transmitter) index is poor.		 1. Check the optical input power and make appropriate adjustments to make it in the specified range; or adjust the attenuation of optical receiver to reduce the output level and improve index.
2. Check the front end machine room optical transmitter RF signal index and make appropriate adjustments.
After connecting the network, the image of the optical contact point has obvious noises. 1. The optical input power of the optical receiver is not high enough, results in the decrease of C/N.
2. The optical fiber connector or adapter of the optical receiver has been polluted.
3. The RF input signal level of the optical transmitter is too low, make the modulation degree of the laser is not enough.
4. The C/N index of system link signal is too low.		 1. Check the received optical power of the optical contact point and make appropriate adjustments to make it in the specified range.
2. Improve the optical received power of the optical contact point by cleaning the optical fiber connector or adapter etc methods. Specific operation methods see “Clean and maintenance method of the optical fiber connector”.
3. Check the RF input signal level of the optical transmitter and adjust to the required input range. (When the input channels number less than 15, should be higher than the nominal value.)
4. Use a spectrum analyzer to check the system link C/N and make appropriate adjustments. Make sure the system link signal C/N﹥51dB.
After connecting the network, the images of several optical contact points randomly appear obvious noises or bright traces. The optical contact point has open circuit signal interference or strong interference signal intrusion. 1. Check if there is a strong interference signal source; change the optical contact point location if possible to avoid the influence of the strong interference signal source.
2. Check the cable lines of the optical contact point, if there is shielding net or situation that the RF connector shielding effect is not good.
3. Tightly closed the equipment enclosure to ensure the shielding effect; if possible add shielding cover to the optical contact point and reliable grounding.
After connecting the network, the images of several optical contact points appear one or two horizontal bright traces. Power supply AC ripple interference because of the bad earth of equipment or power supply. Check grounding situation of the equipment, make sure that every equipment in the line has been reliably grounding and the grounding resistance must be﹤4Ω.
After connecting the network, the received optical power of the optical contact point is unstable and changes continuously. The output RF signal is also unstable. But the detected optical output power of the optical transmitter is normal. The optical fiber connector types do not match, maybe the APC type connect to PC type. The optical fiber connector or adapter may be polluted seriously or the adapter has been damaged. 1. Check the type of optical fiber connector and adopt the APC type optical fiber connector to ensure the normal transmission of optical signal.
2. Clean the polluted optical fiber connector or adapter. Specific operation methods see “Clean and maintenance method of the optical fiber connector”.
3. Replace the damaged adapter.

 

Clean and maintenance method of the optical fiber active connector:

In many times, we consider the decline of the optical power as the equipment faults, but actually it may be caused by that the optical fiber connector was polluted by dust or dirt. Inspect the fiber connector, component, or bulkhead with a fiberscope. If the connector is dirty, clean it with a cleaning technique following these steps:

1. Turn off the device power supply and carefully pull off the optical fiber connector from the adapter.

2. Wash carefully with good quality lens wiping paper and medical absorbent alcohol cotton. If use the medical absorbent alcohol cotton, still need to wait 1~2 minutes after wash, let the connector surface dry in the air.

3. Cleaned optical connector should be connected to optical power meter to measure output optical power to affirm whether it has been cleaned up.

4. When connect the cleaned optical connector back to adapter, should notice to make force appropriate to avoid china tube in the adapter crack.

5. The optical fiber connector should be cleaned in pairs. If optical power is on the low side after clean, the adapter may be polluted, clean it. (Note: Adapter should be carefully operated, so as to avoid hurting inside fiber.

6. Use compressed air or degrease alcohol cotton to wash the adapter carefully. When use compressed air, the muzzle aims at china tube of the adapter, clean the china tube with compressed air. When use degrease alcohol cotton, insert directions need be consistent, otherwise can’t reach a good clean effect.
 

Ứng dụng

Node Quang 870MHz WR8604JL

  • AM CATV
  • Digital CATV
  • DBS & MMDS
  • FTTx PON

Tag :

Ý kiến khách hàng

Sản phẩm cùng loại

Tin Tức Sản phẩm

Không có tin tức phù hợp